1、 In order to reduce the sliding friction between the digital control blade and the material, it is required to use some emulsified oil. After the production and processing of the aluminum wafer, the residual cleaning oil on the upper side cannot be simply wiped off, which requires the removal of special degreaser. The common methods are foam oil removal and self spraying oil removal.

二、自噴除油、去灰：

2、 Self spraying oil and ash removal:

1、加適當?shù)乃謩e稀釋液除油劑和去灰劑；

1. Add appropriate water to separate Paint thinner degreaser and ash remover;

2、調理好噴頭視角；

2. Adjust the perspective of the nozzle properly;

3、保證鋁合金型材工藝品的自噴時間(許多于30秒)；

3. Ensure the self spraying time of aluminum alloy profile handicrafts (many less than 30 seconds);

4、保證鋁圓片有循環系統手洗。

4. Ensure that the aluminum discs have a circulation system for hand washing.

三、侵泡除油、去灰：

3、 Immersion and degreasing, ash removal:

1、在使用前加小量的飲用水，隨后將鋁圓片機加工件滲入池中；(調理好去灰劑)；

1. Add a small amount of drinking water before use, and then infiltrate the aluminum wafer machined parts into the pool; (Adjust the ash remover properly);

2、參加鋁圓片除油劑，在5--10秒內全自動發燙；

2. Participated in aluminum wafer degreasing agent, fully automatic scalding within 5-10 seconds;

3、2~3分鐘除油終結，用飲用水整理；

3. After 2-3 minutes of oil removal, clean with drinking water;

4、進到去灰劑中來灰(時間不跨越30秒左右)；

4. Enter the ash remover to remove ash (time does not exceed about 30 seconds);

5、飲用水整理------風干(暴曬)或是停止空氣氧化。

5. Drinking water treatment - air drying (exposure to sunlight) or stopping air oxidation.

鋁圓片的清理流程:

Cleaning process for aluminum wafers:

1、先用許多的冷水清洗鋁圓片外表有塵垢，隨后在上邊灑經水稀釋液過的洗滌劑，用薄布擦拭鋁圓片的外表，然后用許多的冷水清洗方才清洗后的外表，將鋁圓片外表的臟物都沖跑。

1. First, use a lot of cold water to clean the surface of the aluminum wafer, and then sprinkle the detergent with water Paint thinner on it, wipe the surface of the aluminum wafer with a thin cloth, and then use a lot of cold water to clean the surface of the aluminum wafer after cleaning, and flush away the dirt on the surface of the aluminum wafer.

2、查驗鋁圓片的外表，看一下有沒有沒清潔，有關沒有洗潔凈的在停止重中之重整理，知道一切洗潔凈才行，隨后用冷水將洗濯?jiǎng)┮磺袥_走。

2. Check the appearance of the aluminum wafer to see if it is clean. For those that have not been cleaned, it is important to stop sorting and ensure that everything is clean. Then, rinse off all the detergent with cold water.

3、此外要注意的是不用整理溫度比較高的鋁圓片，由于水份過快的蒸騰就會對外表的噴漆危害，使用洗濯?jiǎng)┑臅r(shí)段，一定要選擇中性化的洗濯?jiǎng)蝗粚?huì)浸蝕鋁圓片的外表。

3. In addition, it should be noted that there is no need to organize aluminum wafers with high temperatures. Due to the rapid evaporation of water, it can cause damage to the surface of the spray paint. When using cleaning agents, it is necessary to choose a neutral cleaning agent, otherwise it will corrode the surface of the aluminum wafers.

本文由鋁卷生產廠家友情奉獻.更多有關的知識請點擊: http://www.generalbaby.cn真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from aluminum coil manufacturers. For more information, please click on: http://www.generalbaby.cn Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned